Announcement

Collapse
No announcement yet.

GP28 windows - FREE

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • GP28 windows - FREE

    Replaced all the sliding windows and port cuddy windows in my 1980 28' Sport Fisher. All six windows are rebuildable or good for parts. Would rather give them away than see them go to the dump. Six free Glasply windows near vancouver WA.
    Thanks, Andy

  • #2
    I'll find a way to get there to prevent them from going to the dump if no one closer bites...

    Comment


    • #3
      Originally posted by Diversified View Post
      Replaced all the sliding windows and port cuddy windows in my 1980 28' Sport Fisher. All six windows are rebuildable or good for parts. Would rather give them away than see them go to the dump. Six free Glasply windows near vancouver WA.
      Thanks, Andy
      And I have 4 for free, front and rear slider for port and starboard sides. Diversified - Also where did you buy your new windows at?
      Mike, I am probably going to Vancouver to order my windows and could pick these up for you.
      "Joint Venture" 1978 midcabin 28', twin 2017 Vortec roller cam "bullet proof" 383/6.3L full roller 350hp engines - You name it, I've either replaced it, restored it, rebuilt it, repainted it or repaired it. That's my job now that I'm retired.

      Comment


      • #4
        Thinking of rebuilding so it would be handy to have extras if the frames aren’t corroded. I’ll take any windows besides the mid cabin specific.

        Comment


        • #5
          These have some corrosion, are rebuildable. The port and starboard cabin windows were reproduced by Motion Windows in Vancouver. The port light windows in the v-birth were reproduced by Bounty Marine.
          Last edited by Bill V; 02-14-2020, 10:49 AM.

          Comment


          • #6
            Originally posted by Diversified View Post
            These have some corrosion, are rebuildable. The port and starboard cabin windows were reproduced by Motion Windows in Vancouver. The port light windows in the v-birth were reproduced by Bounty Marine.
            Could you give me the specs and cost of the Motion Windows you bought. I am visiting them this coming Thursday (20th) to order my port and starboard cabin windows (2 sliders per side). Tint? Frame color? Your thoughts on construction and ease of install?
            "Joint Venture" 1978 midcabin 28', twin 2017 Vortec roller cam "bullet proof" 383/6.3L full roller 350hp engines - You name it, I've either replaced it, restored it, rebuilt it, repainted it or repaired it. That's my job now that I'm retired.

            Comment


            • #7
              The sliding windows Motion built are very close to the originals in construction and material. I wanted them to be as close to the originals as possible, anodized bright aluminum frames, bronze tempered glass with sliding screens. The cost of the four sliders was just under 2K. The overall fit & finish is nice and they work well. You will be smoothing up the openings a bit to get them to slide into the hull, not too bad. I assume you still want to stop by an pick up my old windows for Mike? The GP28 is on my property and not very far from Motion Windows in Orchards.
              Let me know what your schedule is Bill, I'll make sure I'm here.

              Andy 3609316448

              Comment


              • #8
                Thanks again Andy, I stopped by Motion and visited with Jeff. After chatting with him I decided to see if I can make one good set out of two sets. Yours were tinted which was something I wanted and after getting them home and disasembled it looks very good that I can use your glass and my frames. Thanks again Andy, looking forward to seeing you at rendezvous, promise you a ride on my boat too.
                "Joint Venture" 1978 midcabin 28', twin 2017 Vortec roller cam "bullet proof" 383/6.3L full roller 350hp engines - You name it, I've either replaced it, restored it, rebuilt it, repainted it or repaired it. That's my job now that I'm retired.

                Comment


                • #9
                  That's awesome Bill. Had a great time chatting with you. Keep me in mind for props, trailer and the seat for the bridge you mentioned. Looking forward to the rendezvous.

                  Comment


                  • #10
                    Originally posted by Diversified View Post
                    That's awesome Bill. Had a great time chatting with you. Keep me in mind for props, trailer and the seat for the bridge you mentioned. Looking forward to the rendezvous.
                    Yes for sure.Trailer that I talked to you about was sold but it would only work with outboards or I/Os.
                    The seat has your name on it.
                    "Joint Venture" 1978 midcabin 28', twin 2017 Vortec roller cam "bullet proof" 383/6.3L full roller 350hp engines - You name it, I've either replaced it, restored it, rebuilt it, repainted it or repaired it. That's my job now that I'm retired.

                    Comment

                    Working...
                    X